Sunday, October 27, 2019

Importance of chemical reactor

Importance of chemical reactor INTRODUCTION The most important unit operation in a chemical process is generally a chemical reactor. Chemical reactions are either exothermic (release energy) or endothermic (require energy input) and therefore require that energy either be removed or added to the reactor for a constant temperature to be maintained. Exothermic reactions are the most interesting systems to study because of potential safety problems (rapid increases in temperature, sometimes called ignition behavior) and the possibility of exotic behavior such as multiple steady-states (for the same value of the input variable there may be several possible values of the output variable). In this module we consider a perfectly mixed, continuously stirred tank reactor (CSTR), shown in Figure 1. The case of a single, first-order exothermic irreversible reaction, A > B. We will show that very interesting behavior that can arise in such a simple system. In Figure 1 we see that a fluid stream is continuously fed to the reactor and another fluid stream is continuously removed from the reactor. Since the reactor is perfectly mixed, the exit stream has the same concentration and temperature as the reactor fluid. Notice that a jacket surrounding the reactor also has feed and exit streams. The jacket is assumed to be perfectly mixed and at a lower temperature than the reactor. Energy then passes through the reactor walls into the jacket, removed the heat generated by reaction. There are many examples of reactors in industry similar to this one. Examples include various types of polymerization reactors, which produce polymers that are used in plastic products such as polystyrene coolers or plastic bottles. The industrial reactors typically have more complicated kinetics than we study in this module, but the characteristic behavior is similar. The Modeling Equations For simplicity we assume that the cooling jacket temperature can be directly manipulated, so that an energy balance around the jacket is not required. We also make the following assumptions Perfect mixing (product stream values are the same as the bulk reactor fluid) Constant volume Constant parameter values The constant volume and parameter value assumptions can easily be relaxed by the reader, for further study. Parameters and Variables A Area for heat exchange CA Concentration of A in reactor CAf Concentration of A in feed stream cp Heat capacity (energy/mass*temperature) F Volumetric flowrate (volume/time) k0 Pre-exponential factor (time-1) R Ideal gas constant (energy/mol*temperature) r Rate of reaction per unit volume (mol/volume*time) t Time T Reactor temperature Tf Feed temperature Tj Jacket temperature Tref Reference temperature U Overall heat transfer coefficient (energy/(time*area*temperature)) V Reactor volume DE Activation energy (energy/mol) (-DH) Heat of reaction (energy/mol) r Density (mass/volume) The parameters and variables that will appear in the modeling equations are listed Overall material balance The rate of accumulation of material in the reactor is equal to the rate of material in by flow-the material out by flow. Balance on Component A The balance on component A is where r is the rate of reaction per unit volume. Energy Balance The energy balance is where Tref represents an arbitrary reference temperature for enthalpy. State Variable form of Dynamic Equations We can write (1) and (2) in the following state variable form (since dV/dt = 0) where we have assumed that the volume is constant. The reaction rate per unit volume (Arrhenius expression) is where we have assumed that the reaction is first-order. Steady-State Solution The steady-state solution is obtained when dCA/dt = 0 and dT/dt = 0, that is To solve these two equations, all parameters and variables except for two (CA and T) must be specified. Given numerical values for all of the parameters and variables we can use Newtons method (chapter 3) to solve for the steady-state values of CA and T. For convenience, we use an à «sà ­ subscript to denote a steady-state value (so we solve for CAs and Ts). Dynamic Behavior We noted in the previous section that were three different steady-state solutions to the case 2 parameter set. Here we wish to study the dynamic behavior under this same parameter set. Recall that numerical integration techniques were presented in chapter 4. The m-file to integrate the modeling equations iscstr_dyn.m, shown in Appendix 2. The command to integrate the equations is [t,x] = ode45(cstr_dyn,t0,tf,x0); wheret0is the initial time (usually 0),tfis the final time,x0is the initial condition vector.tis the time vector andxis the state variable solution vector. Before performing the integration it is necessary to define the global parameter vectorCSTR_PAR. To plot only concentration or temperature as a function of time, useplot(t,x(:,1))andplot(t,x(:,2)), respectively. Initial condition 1 Here we use initial conditions that are close to the low temperature steady-state. The initial condition vector is [ conc , temp] = [9,300]. The curves plotted in Figure 2 show that the state variables converge to the low temperature steady-state. Initial condition 2 Here we use initial conditions that are close to the intermediate temperature steady-state. The initial condition vector for the solid curve in Figure 3 is [conc, temp] = [5,350], which converges to the high temperature steady-state. The initial condition vector for the dotted curve in Figure 3 is [conc, temp] = [5,325], which converges to the low temperature steady-state. If we perform many simulations with initial conditions close to the intermediate temperature steady-state, we find that the temperature always converges to either the low temperature or high temperature steady-states, but not the intermediate temperature steady-state. This indicates to us that the intermediate temperature steady-state isunstable. This will be shown clearly by the stability analysis in section 5. Initial condition 3 Here we use initial conditions that are close to the high temperature steady-state. The initial condition vector is [conc, temp] = [1,400]. The curves plotted in Figure 4 show that the state variables converge to the high temperature steady-state. In this section we have performed several simulations and presented several plots. In section 6 we will show how these solutions can be compared on the same à ¬phase planeà ® plot. Linearization of Dynamic Equations The stability of the nonlinear equations can be determined by finding the following state-space form and determining the eigenvalues of theA(state-space) matrix. The nonlinear dynamic state equations (1a) and (2a) are let the state, and input variables be defined in deviation variable form Stability Analysis Performing the linearization, we obtain the following elements forA where we define the following parameters for more compact representation From the analysis presented above, the state-space A matrix is The stability characteristics are determined by the eigenvalues ofA, which are obtained by solving det (lI-A) = 0. det (lI-A)=(l-A11)(l-A22)-A12A21 =l2-(A11+A22)l+A11A22-A12A21 =l2-(trA)l+det (A) the Eigen values are the solution to the second-order polynomial l2-(trA)l+det (A) =0(13) The stability of a particular operating point is determined by finding theAmatrix for that particular operating point, and finding the Eigen values of the A matrix. Here we show the Eigen values for each of the three case 2 steady-state operating points. Input / Output Transfer Function Analysis The input-output transfer functions can be found from G(s)=C(sI-A)-1B(14) where the elements of theBmatrix corresponding to the first input (u1 = Tj-Tjs) are the reader should find the elements of the B matrix that correspond to the second and third input variables (see exercise 8) Here we show only the transfer functions for the low temperature steady-state for case 2. The input/output transfer function relating jacket temperature to reactor concentration (state 1) is and the input/output transfer function relating jacket temperature to reactor temperature (state 2) is Notice that the transfer function for concentration is a pure second-order system (no numerator polynomial) while the transfer function for temperature has a first-order numerator and second-order denominator. This indicates that there is a greater à ¬lagà ® between jacket temperature and concentration than between jacket temperature and reactor temperature. This makes physical sense, because a change in jacket temperature must first affect the reactor temperature before affecting the reactor concentration. Phase-plane Analysis In section 4 we provided the results of a few dynamic simulations, noting that different initial conditions caused the system to converge to different steady-state operating points. In this section we construct a phase-plane plot by performing simulations for a large number of initial conditions. The phase-plane plot shown in Figure 6 was generated usingcstr_run.mandcstr.mfrom the appendix. Three steady-state values are clearly shown; 2 are stable (the high and low temperature steady-states, shown as à «oà ­), while one is unstable (the intermediate temperature steady-state, shown as à «+à ­). Notice that initial conditions of low concentration (0.5 kgmol/m3) and relatively low-to-intermediate temperatures (300 to 365 K) all converge to the low temperature steady-state. When the initial temperature is increased above 365 K, convergence to the high temperature steady-state is achieved. Now, consider initial conditions with a high concentration (9.5 kgmol/m3) and low temperature (300 to 325 K); these converge to the low temperature steady-state. Once the initial temperature is increased to above 325 K, convergence to the high temperature steady-state is achieved. Also notice that, once the initial temperature is increased to around 340 K, a very high overshoot to above 425 K occurs, before the system settles down to the high temperature steady-state. Although not shown on this phase-plane plot, higher initial temperatures can have overshoot to over 500 K before settling to the high temperature steady-state. This could cause potential safety problems if, for example, secondary decomposition reactions occur at high temperatures. The phase plane analysis then, is able to à ¬point-outà ® problem initial conditions. Also notice that no initial conditions have converged to the intermediate temperature steady-state, since it is unstable. The reader should perform an eigenvalue/eigenvector analysis for theAmatrix at each steady-state (low, intermediate and high temperature) (see exercise 3). You will find that the low, intermediate and high temperature steady-states have stable node, saddle point (unstable) and stable focus behavior (see chapter 13), respectively. It should be noted that feedback control can be used to operate at the unstable intermediate temperature steady-state. The feedback controller would measure the reactor temperature and manipulate the cooling jacket temperature (or flowrate) to maintain the intermediate temperature steady-state. Also, a feedback controller could be used to make certain that the large overshoot to high temperatures does not occur from certain initial conditions. Understanding Multiple Steady-state Behavior In previous sections we found that there were three steady-state solutions for case 2 parameters. The objective of this section is to determine how multiple steady-states might arise. Also, we show how to generate steady-state input-output curves that show, for example, how the steady-state reactor temperature varies as a function of the steady-state jacket temperature. Heat generation and heat removal curves In section 3 we used numerical methods to solve for the steady-states, by solving 2 equations with 2 unknowns. In this section we show that it is easy to reduce the 2 equations in 2 unknowns to a single equation with one unknown. This will give us physical insight about the possible occurance of multiple steady-states. Solving for Concentration of A as a function of Temperature The steady-state concentration solution (dCA/dt) = 0) for concentration is We can rearrange this equation to find the steady-state concentration for any given steady-state reactor temperature, Ts Solving for Temperature The steady-state temperature solution (dT/dt = 0) is The terms in (17) are related to the energy removed and generated. If we multiply (17) by VrCp we find that Qrem=Qgen Energy Removed by flow and heat exchange Heat Generated by reaction Note the form of Qrem Notice that this is an equation for a line, where the independent variable is reactor temperature (Ts). The slope of the line is and the intercept is. Changes in jacket or feed temperature shift the intercept, but not the slope. Changes in UA or F effect both the slope and intercept. Now, consider the Q gen term Substituting (16) into (20), we find that Equation (21) has a characteristic S shape for Q gen as a function of reactor temperature. From equation (18) we see that a steady-state solution exists when there is an intersection of the Q rem and Q gen curves. Effect of Design Parameters In Figure 6 we show different possible intersections of the heat removal and heat generation curves. If the slope of the heat removal curve is greater than the maximum slope of the heat generation curve, there is only one possible intersection (see Figure 6a). As the jacket or feed temperature is changed, the heat removal lines shifts to the left or right, so the intersection can be at a high or low temperature depending on the value of jacket or feed temperature. Notice that as long as the slope of the heat removal curve is less than the maximum slope of the heat generation curve, there will always be the possibility of three intersections (see Figure 6b) with proper adjustment of the jacket or feed temperature (intercept). If the jacket or feed temperature is changed, the removal line shifts to the right or left, where only one intersection occurs (either low or high temperature). This case is analyzed in more detail in section 7.3. Multiple Steady-State Behavior In Figure 7 we superimpose several possible linear heat removal curves with the S-shaped heat generation curve. Curve A intersects the heat generation curve at a low temperature; curve B intersects at a low temperature and is tangent at a high temperature; curve C intersects at low, intermediate and high temperatures; curve D is tangent to a low temperature and intersects at a high temperature; curve E has only a high temperature intersection. Curves A, B, C, D and E are all based on the same system parameters, except that the jacket temperature increases as we move from curve A to E (from equation (7) we see that changing the jacket temperature changes the intercept but not the slope of the heat removal curve). We can use Figure 7 to construct the steady-state input-ouput diagram shown in Figure 8, where jacket temperature is the input and reactor temperature is the output. Note that Figure 8 exhibits hysteresis behavior, which was first discussed in chapter 15. The term hysteresis is used to indicate that the behavior is different depending on the direction that the inputs are moved. For example, if we start at a low jacket temperature the reactor operates at a low temperature (point 1). As the jacket temperature is increased, the reactor temperature increases (points 2 and 3) until the low temperature limit point(point 4) is reached. If the jacket temperature is slightly increased further, the reactor temperature jumps (ignites) to a high temperature (point 8); further jacket temperature increases result in slight reactor temperature increases. Contrast the input-output behavior discussed in the previous paragraph (starting at a low jacket temperature) with that of the case of starting at a high jacket temperture. If one starts at a high jacket temperature (point 9) there is a single high reactor temperature, which decreases as the jacket temperature is decreased (points 8 and 7). As we move slighly lower than the high temperature limit point (point 6), the reactor temperature drops (also known asextinction) to a low temperature (point 2). Further decreases in jacket temperature lead to small decreases in reactor temperature. The hysteresis behavior discussed above is also known asignition-extinctionbehavior, for obvious reasons. Notice that region between points 4 and 6 appears to be unstable, because the reactor does not appear to operate in this region (at least in a steady-state sense). Physical reasoning for stability is discussed in the following section. Conclusion and future work Finally the conclusion is that a small study on the continuous stirred tank reactor and its model equation after going through we come to know its importance in the chemical engineering field and also its significance as a chemical reactor The future work is that we have to calculate and prove the equation of the continuous stirred tank reactor using Laplace transformation and check it using the MATLAB he equation of the continuous stirred tank reactor using Laplace transformation and check it using the MATLAB

Friday, October 25, 2019

Topic Summary For Petroleum Paper :: essays research papers

CHEMISTRY ISU: REFINEMENT OF CRUDE OIL My ISU will focus on Petroleum, a complex mixture of hydrocarbons that occurs in the Earth in liquid, gaseous, or solid forms. The term is usually restricted to the liquid form, commonly called crude oil, but as a technical term it also includes natural gas and the viscous or solid form known as bitumen. In its liquid and gaseous states, it is also known as Oil, or Crude Oil. Italicized are segments from my ISU or introductions to the planned topics. In my ISU, I plan to dedicate potions of my paper to the following aspects of petroleum. †¢Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Petroleum’s many uses. Petroleum today is the source from which we derive many items. The Motor vehicle’s development in the 1930s gave petroleum a new and swiftly expanding role as the primary source of gasoline; oil and then natural gas replaced coal as the primary fuel for industrial and domestic heating. Petrochemicals derived from petroleum became the source of such chemical products as solvents, paints, plastics, synthetic rubber and fibres, soaps and cleansing agents, waxes and jellies, explosives, and fertilizers. Petroleum fuels also generate a large portion of the world's electrical-power supply. †¢Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  I will also discuss the exploration for crude oil, and the impending crisis if it continues to be used up at the current rates of consumption. ( is expected to exhaust the world’s supply by the mid-21st century) and possible energy alternatives. †¢Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Petroleum’s origin and formation:   Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Petroleum is derived from aquatic plants and animals that died hundreds of millions of years ago. Their remains mixed with mud and sand in layered deposits that, over the millennia, were geologically transformed into sedimentary rock. Gradually the organic matter decomposed into petroleum, which moved from the original source beds to more porous and permeable rocks, such as sandstones and siltstones, where it finally becomes entrapped. †¢Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Types of petroleum; for example, Bitumen. It is formed by crude oil that has migrated toward the Earth's surface and has been stripped of its lighter fractions by descending water. †¢Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  The components of Petroleum:   Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  (A) hydrocarbons. I will spend a lot of time on this segment, as it allows a lot of discussion about hydrocarbons, in which I can discuss chemical compounds and molecular structures and subsequent properties. Can discuss paraffins, naphthenes, aromatics in detail.   Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  Ã‚  (B) Non-hydrocarbons. Other constituents of petroleum include sulfur, oxygen, nitrogen, and the metals nickel and vanadium. Most of these impurities are removed during refining.

Thursday, October 24, 2019

Target for Overnight Rate

The target for the overnight rate-the main tool used by the Bank of Canada to conduct  monetary policy. The Bank carries out monetary policy by influencing short-term interest rates. It does this by raising and lowering the target for the overnight rate. The overnight rate is the interest rate at which major  financial  institutions borrow and lend one day funds among themselves; the Bank sets a target level for that rate. This target for the overnight rate is often referred to as the Bank's  key interest rate  or  key policy rate.Changes in the target for the overnight rate influence other interest rates, such as those for consumer  loans  and mortgages. They can also affect the exchange  of the Canadian dollar. In November 2000, the Bank introduced a system of eight fixed dates each year on which it announces whether or not it will change the key policy rate. The Target for the Overnight Rate is the main tool used by the Bank of Canada to conduct monetary policy f or this reason, it is also known as the policy interest rate.It tells major financial institutions the average interest rate that the Bank wants to see in the market where they lend each other money overnight. When the Bank changes the Target for the Overnight Rate, this change affects other interest rates in the economy. Canada’s major financial institutions routinely borrow and lend money overnight among themselves, in order to cover their transactions at the end of the day. Through the Large Value Transfer System (LVTS), these institutions conduct large transactions with each other electronically.At the end of the day, they need to settle with each other. One bank may have funds left over, while another bank may need money. The trading in funds that allows all institutions to cover their transactions at the end of the day takes place in the overnight market. The interest rate charged on those loans is called the overnight rate. The transmission mechanism of monetary policy The transmission mechanism is the complex chain of cause and effect that runs from the Bank of Canada's actions to changes in asset prices, aggregate demand, the output gap and, eventually, inflation.Among economists, there is some debate about the nature of the transmission mechanism. Engert and Selody (1998), for example, emphasize the important distinction between the passive-money and active-money views of the transmission mechanism and argue that the possibility of making policy errors can be reduced by paying attention to both views. Even among those who agree on the broad nature of the mechanism, there is recognition of considerable uncertainty regarding the timing and quantitative importance of specific linkages.A collection of speeches and research papers published by the Bank of Canada (1996) provides a mainstream  view  of the transmission mechanism. The transmission mechanism is best understood by tracing through the effects of a hypothetical policy decision. For ex ample, consider a situation akin to that in the autumn of 2004, when the Bank had good reason to expect that the solid economic recovery occurring both in Canada and in the global economy would create pressures for Canadian inflation to rise over the coming months. In this case, the Bank's policy response was to raise its target for the overnight interest rate.

Wednesday, October 23, 2019

Awareness to the Health Problem of Violence Against Women

The American Nurses Association (ANA) supports education of nurses, health care providers and women in skills necessary for prevention of violence against women; assessment of women in health care institutions and community settings; and research on violence against women. ANA believes there is a need to increase awareness to the heath problem of violence against women, as well as reduce injuries and psychological misery associated with this crime. ANA believes health care professionals must be educated as to their role in the assessment, intervention, and prevention of physical violence against women. Further, ANA supports the YEAR 2000 Health Objectives, which cite the surveillance, prevention and intervention for violent behavior as a priority issue for the nation. Physical violence against women is behavior intended to inflict harm and includes, slapping, kicking, choking, punching, pushing, use of objects such as weapons, forced sexual activity and injury or death from a weapon. Physical violence is by definition, assault and it is a crime. Ninety-five percent of serious assaults by a spouse or intimate partner are men battering women. Abuse is the leading cause of injury to women and homicide a major cause of traumatic death to women. Physical violence against is pervasive and cuts across all ethnic, racial, religious, and socio-economic groups. Based on national survey results, 1. 8 million women are beaten by their husbands each year. Stated another way, one of every eight husbands assaults his wife at least once during a given year. Abuse during courtship and cohabiting relationships affects between 16 and 23 percent of all dating relationships. The FBI estimates that her male partner will physically assault one in two women during her lifetime. Frequently physical abuse begins during pregnancy with 25-30 percent of pregnant women reporting abuse prior to or during pregnancy. Pregnant women reporting abuse are more likely to deliver a low birth weight infant. Injuries to women sustained from abuse include contusions, concussions, lacerations, fractures and gun shot wounds. Emergency room records document that 22 to 35 percent of women presenting any complaint are there because of symptoms related to physical abuse. Some 1,000 women are killed each year by their male partner, almost always following years of physical abuse. The economic costs of interpersonal violence are high especially if a weapon is involved. The lifetime cost of firearm deaths and injuries are estimated at $23 billion in 1990 with more than 80 percent of the medical care costs borne by public funds. During the same year, injuries caused by interpersonal violence requiring hospitalization cost an estimated $80 billion. Because most physical violence between intimate partners goes underreported, the economic costs are grossly underrepresented. The American College of Obstetricians and Gynecologists, Surgeon General and Centers for Disease Control have forwarded recommendations that all women be routinely screened for physical abuse and offered counseling, education, advocacy and appropriate referrals. Year 2000 Health Objectives cite the surveillance, prevention for violent behavior as a priority issue for the Nation.  · Routine education of all nurses and health care providers in the skills necessary to prevent violence against women Routine assessment and documentation for physical abuse of all women in any health care institution or community setting  · Targeted assessment of women at increased risk of abuse including pregnant women and women presenting in emergency rooms.  · Education of all women as to the cycle of violence, the potential for homicide, and community resources for primary, secondary and tertiary prevention and care.  · Education of school age children and adolescents in public schools about relationships without violence and community resources for help. Research on violence against women, including the development and evaluation of nursing models for preventive assessment, intervention, and treatment for abused women, their children and perpetrators of violence. Partner abuse victims tend to obscure their victimization. They are acutely aware that disclosure of their dilemma will be met with defiance or minimization by their partner, friends, and relatives and by increased abuse by their partners. When a woman becomes independent financially and emotionally the abuse increases the violence by their partner. Some end results are women killing the abusive partner, most of the time it is in self- defense after a history of beatings. Studies have been performed in reference to domestic violence and the abuse of drugs and alcohol. Some abusers are abstainers, however, more are substance abusers than not. The present view is that abusers use alcohol and drugs as an excuse for their violence and drink when are about to become violent. Apparently there seem to be a connection between alcohol and drugs and the severity of violence committed against women. In contrast, victims of domestic violence tend to blame the abuse on the substances used rather than on the abuser personally. The victim acknowledges that they do not enjoy the abuse, but believe their partners philosophy that they deserve the abuse. Victims of domestic violence stay with their abusive partner due to economic status, fear of physical danger to themselves and their children, fear of losing children, lack of job skills, lack of alternative housing, lack of support from family members and friends, lack of information regarding alternatives, fear of court procedures, and fear of partner retaliation. The majority of women have poor self image, are lonely, embarrassed and tend to protect the abuser, they are insecure about themselves and believe their partner is sick and needs their help.  · Backache, abdominal pain, indigestion, headaches, hyperventilation, anxiety, insomnia, fatigue, anorexia, heart palpitations, injuries without explanations and embarrassment about them, hidden injuries to head and neck, internal injuries, genital injuries, scars, burn, joint pain or dislocation, numbness, hearing problems, or bald spots. Injuries from a belt, iron, raised ring, teeth, fingertips, cigarette, gun, or knife, jumpiness or flinching in the presence of the abuser, substance abuse/suicidal thoughts or attempts, denial of any problems in their relationship, lack of relationships of friends or family, isolation or confinement to home. Believing in family unity at all costs and in traditional stereotypes, an overzealous partner who does not want to leave spouse alone in an emergency care unit. Battered woman syndrome is being suggested as a sub classification of PTSD due to repetitive abuse being a serious threat to the victim†s health and life. Battered women report nightmares, flashbacks, recurrent fears of more violence, emotional detachment, numbness, startle response, sleep problems, impaired concentration, and hyper vigilance. Victims show reactions to chronic trauma, but no symptoms of psychopathology are present. How can we help? We can offer information and assistance to these individuals who are victimized by their partners. Recognizing the symptoms (listed above) is the first step in offering assistance. Make an assessment (length/frequency of abuse, types of abuse; physical, psychological, sexual, financial) and recommend the victim to available services offered in the surrounding area. Do not be judgmental, be objective, and non threatening, ask directly if abuse is occurring, identify the abusers behavior, acknowledge the seriousness of the abuse, help the victim to asses internal strengths, encourage use of personal resources, give the victims a list of shelters, police departments, legal assistance, and financial aid, allow the victim to choose his or her own options, teach victim to develop a safety/escape plan, tell the abuser to stop the abuse and get himself help, do not blame the victim, do not get angry with the victim, refuse no help to the victim even though they are not ready to leave the abuser, do not retaliate with the victim against the abuser, do not encourage the victim to leave the abuser before she is ready. It is however, important to assure the victims they are not alone and they do not deserve the abuse they have become accustomed to. We must impart to them that they have dignity and worth and acknowledge their mental and physical exhaustion, fears, ambivalence about the abusers and leaving, and their wish to help the abuser as well as themselves. The victim may want to try counseling with a community agency or a local pastor, do not discourage this, it is always the victims decision on how to go about, stopping the violence in their own life.

Tuesday, October 22, 2019

Essay on Summative Week 2 Part B

Essay on Summative Week 2 Part B Essay on Summative Week 2 Part B Executive Summary One of the key decisions you'll make when starting a business is which legal structure to use. Because it's such an important decision, you should get advice from a qualified independent business, financial or legal advisor. A business name is simply a name or title under which a person, or other legal entity, trades. It not only identifies you to your customers, but also allows you to differentiate yourself from your competitors and enables your customers to make an emotional connection to your business and brand. For many businesses, the name is often the most valuable asset. Decisions made by Business Structures and Business Name also directly impact within the financial advisory services firm which provides advisory service on various types of accounting and business compliance and management issues. Introduction This report will contain information related to legal requirements to setup the Business Structures also advantages and disadvantages of each business structures in Australian. The process of registering a Business Name in NSW for presentation to the client also provided to the relevant section of various legislation and common law. Main Contents 1. Business Structures you choose will depend on the size and type of business, along with your personal circumstances and how much you want to grow the business. Keep in mind that if you need to, you can change your business structure later on if you find that a new structure will meet your needs better. 1. Public companies Legal Requirements Profit/asset test Shareholder spread Certain constitutional and corporate governance requirements Prospectus for the capital raising, a minimum issue price of $0.20 Advantages There is limited liability for the shareholders The business has separate legal entity. These businesses can raise large capital sum as there is no limit to the number of shareholders. Disadvantages There are lot of legal formalities required for forming a public limited company it is costly and time consuming The original owners may lose control Public Limited companies are huge in size and may face management problems such as slow decision making and industrial relations problems. 2. Private companies Legal Requirements Deciding if a company structure is right for you Choosing a company name Deciding how to operate your company Understanding your legal obligations as an officeholder Getting the consent of those involved in your company Registering your company, and Understanding your legal obligations regarding your company name, Australian Company Number (ACN) and Australian Business Number (ABN). Advantages Your liability for the company’s debts is limited, although this protection can be destroyed by creditors, including financiers, calling for guarantees from company directors It’s easy to transfer ownership by selling shares to another party Shareholders (often family members) can be employed by the company Taxation rates can be more favourable You’ll have access to a wider capital and skills base. Disadvantages The company can be expensive to establish and maintain You are required to provide annual and other returns to the Australian Securities and Investment Commission (ASIC) Your financial affairs are public Directors’ activities are scrutinised by ASIC It can be costly to wind up the business. 3. Trusts Legal Requirements Written trust agreement Business name registration Registering for an ABN number with an Australian address Advantages Limited liability is possible if a corporate trustee is appointed The structure provides more privacy than a company There can be flexibility in distributions among beneficiaries Disadvantages The structure is complex The Trust can be expensive to establish and maintain Problems can be encountered when borrowing due to additional complexities of loan structures 4. Partnerships Legal Requirements Written agreement Business name registration Registering for an ABN number with an

Sunday, October 20, 2019

Earth Population Essays - Demography, Human Overpopulation

Earth Population Essays - Demography, Human Overpopulation Earth Population Our Earth has changed more dramatically in the 20th Century then in any other time period previous. During this time the health of our planet has also been both harmed and improved in dramatic ways. Two examples are that in this century, we have produced more air pollution then ever before, but our nature conservation efforts are working. Based on that type of logic, it is usually very easy for a scientist to tell if a particular change in our environment during the 20th Century, was good or bad for our planet. That is where population growth comes in and breaks this idea. Is population growth good or bad for our world? This is a question which scientists around the world have been debateing about for decades. The purpose of this essay will address that question. It will also talk about the future growth rate of our world's population, what if any relationship can be drawn from over population and the GNP and literacy levels in a country, what types of population control measures the four largest countries use, and finally determine if there are any population problems and find solutions for them. Despite extensive population control measures, the country with the largest population is China. In fact China contains almost one-fourth of the world's people at around 1.2 billion. During the 1950's the population grew at a rate of 2% per year. The rate of growth slowed to 1.3% by 1990, in part due to population control measures. China's population control measures are based around a creul policy allowing parents only one child. This policy has led to higher levels of abortion, sterilizations, and inficide than in any other country in the world. The dramatic declines in China's population growth rate have however taken place well before the one child policy went into effect in 1979. This further confuses experts who study population and try to determine why population rates flucuate. Some of these experts suggest that aside from the one child policy China's growth rate might have decreased from 2.0 to 1.3 percent because of major improvements in infant mortality rates. Thus parents had more confidence that their children would live to maturity. Also, as China has moved to become a more industrialized country families have chosen to reduce family size. For example in our country 200 years ago families were large because the more kids a family had the more successful the farm would be. Those are a few reasons the population rate in China might be lower than in years previous and continue to slow down.

Saturday, October 19, 2019

A Review On Enterprise Resource Planning Systems Information Technology Essay

A Review On Enterprise Resource Planning Systems Information Technology Essay INTRODUCTION â€Å"An enterprise resource planning (ERP) systems is that they integrate across functions to create a single, unified system rather than a group of separate, insular applications†. As ERP system is providing optimal solutions and strong control over the company operations, every business is looking forward for this adoption. Since currently available ERP softwares are charging at higher level of licencing and supporting costs, businesses are in the necessity of finding an open source alternative. This document provides the feasible open source alternative option to the current market leader in the proprietary ERP – SAP ECC. Open Source ERP Systems: The following are the popular open source ERP systems available in the latest market. Though there are many number of open sources are available like Opentaps, Ofbiz, ERP5, and so on here only considered few which are moderately fulfil business requirements in compare with SAP solutions. Adempiere This is one of the major ERP leaders in the open source technologies and has been resulted most successful in small and medium industry users mainly in Retail, Trading, Manufacturing and service sectors. [Adempiere Release Manual]. This is highly motivated and active community based software and is in the top 5 positions according to sourceforge.net. Compiere In the current era, Compiere is the most popular open source ERP+CRM application. It is a comprehensive solution for SME’s. This provides solutions in Distribution, Retail, Manufacturing and Service industries with highly adaptable and easy to use enterprise class applications. In ERP, first time Compiere started revolutionary design through which applications are enabled with easy customization and extension without any programing. Openbravo This is more commercial oriented open source ERP. ERP solution provides a robust application which integrates distribution, inventory, E-commerce, accounting and point of sale workflows. This h as been received continuously best open source awards in 2009 and 2010 from Infoworld and many more recognitions from various Organizations. It is developed in java and oracle, postgres SQL databases can be used. OpenERP(Farmer TinyERP) This is comprehensive suite for all operations of an Enterprise. It follows the modular approach which helps customer to initiate one application and then add others as they go. This is designed through a famous 3 tier MVC architecture. Written in Python and Database is PostgreSQL. Clients are required to install flash components in their web browser to access. OpenPro OpenPro is a leader in licensed Enterprise Resource Planning (ERP) software using open source technology and also this is the first web based ERP software started on demand in the market since 1988. This software designed as a platform independent and is written in open source php. Over the years, Software has shown continuous improvements by providing advanced features along with appl ication stabilization. This is recognized as best suited for the larger businesses. Open Source ERP Pros and Cons The following are the advantages and disadvantages of above open source alternatives. ADempiere Advantages: Architecture Model driven Architecture Active data dictionary – reducing 80% coding work in customization Browser/Server + Client/Server Database independent : PostgresSQL/Oracle/ (MySQL) Function & Structure